A Thermostat refrigeration control device is used to make sure that the bearings in a compressor are receiving proper lubrication.
What are refrigerant manipulate devices?A tool for controlling the waft of refrigerant to the circuits of a multi-circuit evaporator in a refrigeration system, comprising an orifice plate having a refrigerant enlargement orifice and a distributor plate having passages into which interchangeable metering jets are inserted.
The thermostat controls the cooling system by tracking the temperature after which switching the compressor on and off. When the sensor senses that it is bloodless sufficient internal a refrigerator, it turns off the compressor. If it senses an excessive amount of heat, it switches the compressor on and starts off evolving the cooling system again.
Read more about the control device :
https://brainly.com/question/730146
#SPJ1
What are the two (2) different design elements of scratch?
Answer: There is four elements of Scratch. The stage, the sprites, the script and the programming palette.
Explanation:
Determine the power output of the draw-works motor M necessary to lift the 600-lb drill pipe upward with a constant speed of 4 ft/s. The cable is tied to the top of the oil rig, wraps around the lower pulley, then around the top pulley, and then to the motor.
Answer:
[tex] \therefore [/tex] The power output of the draw-works motor is 4.36 hp
Explanation:
Given that,
600 lb of weight of the drill pipe 4 ft/s constant velocity of the motorM power output of the motorAs the problem given, the cable is tied of the top on the oil rig and it wraps around the lower pulley and the top pulley. So, we will be using the formula below:
[tex] \boxed{\rm{2s_p + s_M = l}} [/tex]Differentiate it but with respect to the time. Therefore,
[tex] 2v_p +v_M = 0 [/tex]Thus,
[tex] V_M = -2v_p = -2(-4) = 8 \ ft/s [/tex]Thus, the power output should be
[tex] P = Fv = \bigg(\frac{600}{2}\bigg) \cdot 8 = 2400 \ lb \cdot ft/s = \frac{2400}{550} = 4.36 \ hp [/tex]
[tex] \therefore [/tex] The power output of the draw-works motor is 4.36 hp
If a 1500 V load is ac coupled to the output in Figure 9–60, what is the resulting output voltage (rms) when a 50 mV rms input is applied? gm = 5000 mS.
The resulting output voltage (rms) when a 50 mV rms input applied is -187.5 mV.
What is rms voltage?Root Mean Square Voltage is the amount of AC power which produces the same heating effect as DC Power would have produced.
Vo = -gm x Vi (Rd II Rl )
Vo = -5000 x 10⁻⁶ x 50 x 10⁻³ x (1.5k II 1.5k )
Vo = -25 x 10⁻² x 750 x 10⁻³
Vo = -187.5 mV
Hence, resulting output voltage (rms) when a 50 mV rms input applied is -187.5 mV.
Learn more about rms voltage.
https://brainly.com/question/13507291
#SPJ1
Explain the surprising realization scientists are making about bacteria and what danino hopes to eventually be able to do using bacteria. hurry 30 points
The surprising realization scientists are making about bacteria and what danino hopes to eventually be able to do using bacteria are the Corallococcus exercitus.
Who discovered the bacteria?Antonie van Leeuwenhoek used single-lens microscopes, which he made, to make the primary observations of micro organism and protozoa. His full-size studies at the boom of small animals inclusive of fleas, mussels, and eels helped disprove the concept of spontaneous era of life.
Researchers found a brand new species of alga in vital New York and named it Gormaniella terricola, with the genus named after poet Amanda Gorman.
Read more about the bacteria:
https://brainly.com/question/25236237
#SPJ1
1. Explain the difference between energy and power (2)
Explanation:
Energy is what makes change happen and can be transferred form one object to another. Energy can also be transformed from one form to another. Power is the rate at which energy is transferred. It is not energy but is often confused with energy.
Answer:
• Energy is the ability to do work, and it can be transferred from one body (or system) to another, but is always conserved.
• Power is the amount of energy transferred per unit time.
Hope this helps!
Technician a says that the intake valve is closed during the power stroke. technician b says that the exhaust valve is closed during the compression stroke. who is right?
Answer:
trick question - they are both right.
Explanation:
Both valves are closed during compression and power stroke or both strokes would be useless.
Question 2: write a program for smart garage system using:
2 IR obstacle sensor, relay & LCD.
The garage have 25 space to 25 car & have also two doors entrance & exist; first IR sensor on
entrance and second IR sensor on exist. This system counts how many empty spaces for parking.
When the car enters the sensor on entrance activate & the counter decreases, when the car exists the
sensor on exist activate & the counter increase. Use LCD to print how many empty spaces in the
garage, and finally when the garage full the LCD must print this message "Garage Full "and the
relay close to shut down the entrance door.
Answer:
C
Explanation:
Roads in urban areas are generally
Answer:
they probably have more sidewalks and traffic lights.
Explanation:
a lot of people live in urban areas.
A cutting tool wears out with a time to failure that is normally distributed with a mean of 10 working days and a standard deviation of 2.5 days. (a) determine its design life for a reliability of 0.99. (b) find the reliability if the tool is replaced every day; every two days; every five days. (c) determine the probability that the cutting tool will last one more day given it has been in use for 5 days.
Using the normalized distribution it is possible to calculate the value of Z score and for cases where there is a 99% chance, so Zscore is -3.6 and X= 16.45.
What are the types of probability distribution?This curve determines the probability of the event associated with it occurring. The Gaussian distribution is the most common, hence it is known as the Normal Distribution. The area under the distribution curve is always equal to 1.0.
The formula for this distribution can be described as:
[tex]Z score = \frac{x-\mu}{\sigma}[/tex]
Where:
x= Probability density functionμ= Meanσ= Standard DeviationIn this case,
[tex]Z score =\frac{1-10}{2.5} \\Z score = -3.6[/tex]
P-value from Z-Table will be P(x<1) = 0.00015911
For 99% we have that z will be 2.58, so
[tex]2.58=\frac{x-10}{2.5}\\x = 16.45[/tex]
See more about normally distributed at brainly.com/question/15103234
#SPJ4
Is it possible to create an iron man suit if yes what do i need to build it
Answer: Money, Jesus, Metal, and an infinity stone gold-titanium alloy.
Explanation: yes
jumble letters for WROBN plsss answer
Answer:
brown.
Explanation:
it could be brown.
thermal energy measured by?
Answer:
Thermal energy is measured using a thermometer denominated in Fahrenheit, Celsius and Kelvin
True or false. flashing arrow panels are only used at night.
The flashing arrow panels are not used just at night but are used even during the day time. These are necessary to give the directional information to the drivers. Thus, the given statement is false.
What are the safety instructions?The safety instructions are necessary for the drivers as absence of these would lead to increased number of accidents which could lead to death of a number of people. The flashing arrow panels is one of these instructions.
Flashing arrow panels are used during the day as well as at the night to give advance warning and directional information to the drivers where it is required to move to the right or to the left into another lane.
Some of the safety systems used at level crossings include amber and red warning lights on majority of roads, people should stop when the amber lights come on, unless vehicle has already crossed the stop line.
Learn more about Driving here:
https://brainly.com/question/2619161
#SPJ5
What is the objective of phasing out an INDUCTION MOTOR before putting the machine into commission?
The main objective of phasing out an INDUCTION MOTOR is to identify the ends of the stator coils.
What is an induction motor?An induction motor is a device based on alternate electricity (AC) which is composed of three different stator coils.
An induction motor is a device also known as an asynchronous motor due to its irregular velocity.
In conclusion, the objective of phasing out an INDUCTION MOTOR is to identify the ends of the stator coils.
Learn more on induction motors here:
https://brainly.com/question/15721280
#SPJ1
8. A voltmeter measures a voltage drop of 600 V across a heating element while an
ammeter reads the current through it as 2.0 A. What is the resistance of the
heating coil.
Answer:
How do I calculate voltage drop?
To calculate voltage drop, E, across a component, you need to know the resistance of the component and the current thru it. Ohm's Law is E=I⋅R , which tells us to then multiply I by R . E is the voltage across the component also known as voltage drop
Explanation:
51.
What is a subpanel?
Answer:
im pretty sure its answer D
Explanation:
When two watercraft are crossing each other's paths, which should
assume the give-way responsibility?
The watercraft in the crossing are given with the responsibility to the starboard side to give the way and avoid collision.
What are crossing rules?The crossing rules are given as the safety rules that are mediated in order to avoid the collision accidents when the two vehicles are crossing the path.
In the sea, the rules are given with the watercraft at the starboard side or the giveaway side to make the way to the other watercraft and avoid collision.
Learn more about crossing rules, here:
https://brainly.com/question/4773184
#SPJ1
True or false?Inventory-risk costs are a form of carrying costs.
or...................
Answer:
i believe it is true
Explanation:
In a safety seminar at a nuclear power plant, a technician describes the procedure used if temperatures in the reactor become too high. What procedures should the technician describe?
The procedures that the technician should describe are:
More coolant will be pumped into the reactor.The fuels rods will be lowered into the reactor.What is Nuclear power?This is known to be the method that employs the use of nuclear reactions to create or produce electricity.
Note that in the above scenario, The procedures that the technician should describe are:
More coolant will be pumped into the reactor.The fuels rods will be lowered into the reactor.This is because the coolant will help to reduce the heat level in the reactor and
the fuel rods is needed to power the reactor.
See full question below
In a safety seminar at a nuclear power plant, a technician describes the procedure used if temperatures in the reactor become too high. What procedures should the technician describe?Select all that apply.- May be more than one answer
a. More coolant will be pumped into the reactor.
b. The control rods will be taken out of the reactor
c.The fuels rods will be lowered into the reactor.
d. The control rods will be lowered into the reactor.
Learn more about nuclear power from
https://brainly.com/question/24295936
#SPJ2
Why do we study National studies
Answer:
It’s so we can then understand other cultures and other ways that people do things or we can also be prepared for what a country that we have not been to yet is going to relatively be like. This can also help with vacation planning.
Explanation:
it can also help us understand different people from different cultures.
What are the philological elements of interior design most like?
o a well-selected outfit that gives people an idea of who the wearer is
a public address glven via the intercom system of a large building
o a perfectly written letter that exactly conveys the writer's point
o a complex but silent conversation between two people in sign language
Answer:
Ea public address glven via the intercom system of a large buildingxplanation:
The building areas where loose fill insulation is most commonly used are
Answer:
Loose-fill insulation can be installed in either enclosed cavities such as walls, or unenclosed spaces such as attics
Explanation:
Answer in one of my classes
250 volts are applied to a toaster oven which draws a current of 12 A.
What is the toaster oven's resistance?
Answer:
20.833 ohms
Explanation:
V = IR re-arrange
V/I = R
250 / 12 = 20.833 ( 20 5/6)
* Question 1: Design alarm system as shown below. The alarm turns on when one of the following
conditions happened:
A. Motion IR sensor & window sensor
activated.
B. Motion IR sensor & door sensor
activated.
C. Otherwise the buzzer off.
(A)
Warning
Motion
Sensors
Buzzer
Suppose that: Warning buzzer on pin 8
Motion sensor on pin 5
Window sensor on pin 6
Door sensor on pin 7
The buzzer works on beating mode.
(C)
Door
sensor
TE
(B)
Window
Sensors
Answer:
A
Explanation:
Blank is common during exercise.
Answer:
Sweat
Explanation:
As you exercise you respire and warm up due to energy. In turn, two things happen, blood vessels vasodilate (irrelevant to you) and sweat glands sweat more. this sweat then evaporates and cools down the body.
Answer:
Hyperpnea is common during exercise
Explanation:
Edge 2023
if you were to create your own watershed using materials from your house, what materials would you need, and why would you need these materials to create a watershed?
Answer:
A pan (baking)
Newspaper
Cloth
(colored) Water
A binder (to elevate one side of the pan)
Explanation:
hope this helps:)
1. what helped inspire ms. shotwell to become an engineer?
i
2. what is the purpose of the launch escape system for dragon? how does it work?
3. what is one specific reason spacex is successful according to ms. shotwell?
4. what is one example of how physics was used to drive spacex design?
5. why is the satellite internet project difficult for spacex?
6. what is space debris? what is spacex doing to help decrease the amount of debris?
7. what is one way the big falcon rocket (bfr) can be used to make a difference in the world?
8. what are two ways spacex plans to change personal travel?
9. what is your personal opinion of the future goals of spacex? do you believe they will be achieved?
why or why not?
10. would you be willing to travel with spacex in the future? why or why not?
|
The action that inspire Ms. Shotwell is that Her mom took her to a trip to look at the Society of Women Engineers event, and she was said to have quickly fall in love with a mechanical engineer who was a speaker in the event.
What is the purpose of the launch escape system for dragon?The LES is mad up to separate the spacecraft from the Falcon 9 rocket and move the crew away to safety in case any event of any emergency.
SpaceX was said to be successful because:
It consist of two NASA astronauts.It is made up of The Crew Dragon's launch escape system (LES).It is made up of a set of eight SuperDraco engines.Note therefore, that the action that inspire Ms. Shotwell is that Her mom took her to a trip to look at the Society of Women Engineers event, and she was said to have quickly fall in love with a mechanical engineer who was a speaker in the event.
Learn more about Engineers from
https://brainly.com/question/17169621
#SPJ4
the most important element in the regulation of the hts is the
Answer:
Explanation:
the driver who obeys traffic laws
A continuous fiber-reinforced composite is to be produced by dispersing 60 vol% carbon fibers in a polycarbonate matrix. if the stress in the polycarbonate matrix when the carbon fibers fail is 45 mpa, the longitudinal elastic modulus of the composite using rule of mixture is
Answer:
Explanation:
A continuous fiber-reinforced composite is to be produced by dispersing 60 vol% carbon fibers in a polycarbonate matrix. if the stress in the polycarbonate matrix when the carbon fibers fail is 45 mpa, the longitudinal elastic modulus of the composite using rule of mixture
when servicing piston rods and pins it is important to always
Answer:
Pistons should be inspected and measured.
Explanation:
