You serve a volleyball with a mass of 2.1kg the ball leaves your hand with a speed of 30 m/s. What is the kinetic energy of the ball?
Answer:
945 joules
Explanation:
the formula for kenetic energy is:
0.5 × m × v^2
where m is in (kg) ane (v) is in meter per second.
so we can just use the formula;
0.5 × 2.1 × 30^2
so the answer is 945 joules
1. 50 W and 100 W lamps are designed for the same voltage. Which lamp has the higher filament resistance and why?
2. At a voltage of 4 V, 300 mA flows through the bulb. What is the work done by the electric current in 5 min?
3. The label on the lamp says 100 W, 220 V. Calculate the resistance of the lamp?
4. What is the work done by the motor of a floor polisher in 25 min with a voltage of 220 V, a current rating of 1,25 A and a motor efficiency of 80%?
help
Answer:
Look below.
Explanation:
1.) The resistance of a light bulb filament is effected by both length and cross-sectional area. Thicker wires have less resistance. A 120-Watt bulb has a greater current and a smaller resistance. Thus, a 120-Watt bulb must have a thicker filament than a 60-Watt bulb (assuming the lengths of the filaments are identical). We also think of lightbulbs in terms of their power ratings in watts. Let us compare a 25-W bulb with a 60-W bulb. Since both operate on the same voltage, the 60-W bulb must draw more current to have a greater power rating. Thus the 60-W bulb’s resistance must be lower than that of a 25-W bulb. If we increase voltage, we also increase power. For example, when a 25-W bulb that is designed to operate on 120 V is connected to 240 V, it briefly glows very brightly and then burns out. Precisely how are voltage, current, and resistance related to electric power?
2.) Energy transferred = 120 × 2 = 240 J. This equation can be rearranged to V = E ÷ Q. So voltage is energy transferred divided by charge.
3.) Power= Voltage × Current
4.) W=Pt
Which sound frequency could a human detect? 1 hertz 10 hertz 50 hertz 50,000 hertz.
Answer:
Good human ears can detect sound from about 50 Hz to about 20,000Hz (20 kHz); this can be called the audible range of frequencies.
so c.50 hertz
Explanation:
Hope it helps :)
Answer:
50 hertz
Explanation:
This is right
What is the momentum of an object that has a mass of 0.03 grams and a velocity of 1200 m/s2
answer is 36
because the formulae of momentum is
mass×velocity
You want to determine whether the mass of an object attached to a parachute affects the time it takes to fall to the ground. In this investigation, would "the material the parachute is made out of" be a suitable control variable? no or yes
The material the parachute is made out of" will not be a suitable control variable as it is needed in the research.
What is a control variable?It should be noted that a control variable simply means any variable that is held constant in a research.
In this case, the material the parachute is made out of" will not be a suitable control variable as it is needed in the research.
Therefore, it's false.
Learn more about mass on:
https://brainly.com/question/19385703
Question 3 of 20
A crate falling from a plane is part of a closed system that has 24450 J of
mechanical energy. If the kinetic energy of the crate increases from 10,000 J
to 15,000 J, what happens to the gravitational potential energy of the system?
A. It decreases from 15,000 J to
10,000 J.
B. It increases from 9450 J to
14,450 J.
C. It decreases from 14,450 J to
9,450 J.
O D. It increases from 10,000 J to
15,000 J.
Old potential energy:-
PE+KE=MEPE=ME-KEPE=24450-10000PE=14450JNew potential energy
PE=24450-15000PE=9450JOption B is correct
If we say that a galaxy has a lookback time of 1 billion years, we mean that _________.
Answer:
its light traveled through space for 1 billion years to reach us
Explanation:
How is the duration and intensity of daylight related to the suns apparent path?
Answer:
I dont know but ask a tutor
Explanation:
MOnkey Srry
A flywheel is rotating with an angular velocity of 1.4 rad/s and is acted on by an acceleration of 0.6 rad/s².
a) What angular velocity will it have attained after three complete turns?
b) How long will it take to do those three turns?
(a) The final angular velocity of the flywheel after 3 complete revolutions is 4.96 rad/s.
(b) The time taken for the flywheel to make 3 complete revolutions is 5.93 s.
Final angular velocityThe final angular velocity of the flywheel after 3 complete revolutions is determined by applying third kinematic equation as shown below;
θ = 2π (rad/rev) x (3 rev) = 18.85 rad
ωf² = ωi² + 2αθ
ωf² = (1.4)² + 2(0.6)(18.85)
ωf² = 24.58
ωf = √24.58
ωf = 4.96 rad/s
Time of motionThe time taken for the flywheel to make 3 complete revolutions is calculated as follows;
ωf = ωi + αt
t = (ωf - ωi)/α
t = (4.96 - 1.4)/0.6
t = 5.93 s
Learn more about time of motion here: https://brainly.com/question/2364404
Which condition is necessary for a lunar eclipse to occur?.
For a lunar eclipse to occur, the Sun, Earth, and Moon must be roughly aligned in a line. Otherwise, the Earth cannot cast a shadow on the Moon's surface and an eclipse cannot take place. When the Sun, Earth, and Moon come together in a straight line, a total lunar eclipse takes
If a wave has the length of 2 meters and it takes the wave 6 seconds to pass calculate the wave speed
Answer:
12 m/sec
Explanation:
lambda = 2 m
period = 6 seconds frequency = 1/p = 1/6
speed = lambda * freq
= 2 / 1/6 = 12 m/s
A radioactive sample starts with 800,000 undecayed nuclei. After 12 hours, 700,000 of the nuclei have decayed. What is the half-life of the sample?
A. 3 hours
B. 12 hours
C. 6 hours
D. 4 hours
Answer:
100,000 / 800,000 = 1 / 8 amount of sample after 12 hours
(1/2)^n = 1 / 8 after n half-lives 1/8 of sample will be left
n = 3
(D) is the correct answer - 1/2 half-life = 4 hours
Mike stands on a scale in an elevator. If the elevator is accelerating upwards with 4.9 m/s2, the scale reading is ____ times Mike's weight.
Answer:
F - M a force exerted by scales on student
M a = M (9.8 + 4.9) m/s^2 upwards chosen as positive
a = 1.5 g net acceleration of student due to force of scales
W =M g weight of student (actual weight)
Wapp = M 1.5 * g apparent weight (on scales) of student
In an elevator which is accelerating upwards with 4.9 m/[tex]s^{-2}[/tex], Mike's weight will be 1.5 times the actual weight.
In the question, it is given that the lift is accelerating upwards with 4.9 m/[tex]s^{-2}[/tex] Let Mike's weight be "m", "g" is acceleration due to gravity and "a" be the upward accelerationThe upward acceleration of lift = 4.9 m/[tex]s^{-2}[/tex]As the lift is accelerating upwards, the apparent weight (R) = m (g+a)Apparent weight R = m*(9.8+4.9) NApparent weight R = m*(9.8+4.9)/9.8 KgfApparent weight R = m*1.5Hence, the apparent weight will be 1.5 times the real weight.
To know more about the relationship between an object accelerating upwards and the weight of the object, refer:
https://brainly.com/question/2293244
#SPJ2
Since many wavelengths of light are measured in nanometers, it's useful to know that planck's constant (h) multiplied with the speed of
light (c) is equal to 1240 eVnm.
This is useful, as E = hf, or otherwise written as E= .
With this information in mind, solve the following:
A photon has 1.6 eV of energy. What is the wavelength of this photon?
O a
410 nm
Ob
775 nm
Ос
1984 nm
Od
306 nm
Answer:
E = h f and since f = c / λ we have E = h c / λ
Thus λ = h c / E
Also, 1 ev = 1.6E-19 C
λ = 6.63E-34 * 3.0E8 / (1.6 * 1.6E-19)
λ = 6.63 * 3.0 / (1.6 * 1.6) * E-7
λ = 7.77E-7 = 777 nanometers
(B) is correct
Which of these invertebrates have asymmetric bodies?
Answer:
Sponges
Explanation:
It would be either sponges or flatworms.
I apologize if it is incorrect-
I hope it helps! Have a great day!
Anygays-
a car of mass 800 kg is travelling at 12m/s the car accelerates over a distance of 240 m there force causing this acceleration is 200 newton determine the work done on the car and its final velocity car
Answer:
See below
Explanation:
Force X distance = work
200 N * 240 m = 48 000 N-m = 48 000 j
F = ma
200 = 800 a
a = 1/4 m/s^2
d = v t + 1/2 a t^2
12 m/s t + 1/2 1/4 m/s^2 t^2 = 240
shows t = 17 sec (via Quadratic Formula)
final velocity = 12 + at = 12 + 1/4(17) = 16.26 m/s
A toy car pushed across the floor is observed to slow down and stop based on Newton’s first law of motion what is the best conclusion
A : an object in motion eventually stops
B. The car must have been going slightly uphill
C. The car did not have enough mass to keep going
D. There must have been an unbalanced force acting on the toy car
An object in motion eventually stops because of friction.
What is Newton’s first law of motion?Newton's first law states that if a body is at rest or moving at a constant speed in a straight line, it will remain at rest or continue its moving in a straight line at constant speed unless force is applied on it.
So we can conclude that An object in motion eventually stops is the correct answer.
Learn more about law here: https://brainly.com/question/820417
Which is a situation where two hockey pucks could have equal but opposite momentums? Assume that the ice is a frictionless surface.
A. if the hockey pucks weigh the same.
B. if the hockey pucks exert the same force on each other in the same direction while traveling at the same speed.
C. if the hockey pucks are traveling at the same speed, bounce off each other, and move in the opposite direction.
D. if the hockey pucks have the same mass.
The dimensions of a triangle are shown below.
What is the area of the triangle?
Answer:
7. answered because ia an pro
Explanation:
[tex]area = \frac{1}{2} bh[/tex]
[tex]area = \frac{1}{2} \times 60 \times 50[/tex]
[tex]area = \frac{3000}{2} [/tex]
[tex]area = 1500mm ^{2} [/tex]
Suppose that your car is stuck on ice. The wheels spin, but the car does not move. Your friend suggests that you let the air out of the tires to increase the amount of friction. What are some reasons your friend might think this? Discuss whether or not these reasons are consistent with what you have learned about friction.
Explanation:
The center of mass of a system acted on only by internal forces cannot accelerate. without friction a car cannot move. This is a consequence of Newton's third law
How are solar flares different from solar prominences.
Answer:
What is the difference between a prominence and a solar flare? A prominence is a loop of cool incandescent gas that extends above the photosphere. A solar flare is an explosive release of energy that comes from the sun and causes magnetic ditrubances.
Explanation:
Which terms describe the different movements of earth? check all that apply. rotation revolution tilted orbit lunar cycle elliptical orbit
Revolution and rotation are the terms that describe the different movements of the earth.
What is the earth?Our home planet is Earth. Earth and its moon, according to scientists, originated about the same period as the rest of the solar system.
That would have been around 4.5 billion years ago, according to scientists. Earth is the solar system's fifth-largest planet.
The rotation and revolution of the earth are two different movements. The movement of the earth on its axis is known as rotation.
Revolution is the movement of the earth around the sun in a fixed route or orbit. The earth's axis, which is an imaginary line, forms a 6612° angle with its orbital plane.
Hence revolution and rotation are the terms that describe the different movements of the earth.
To learn more about the earth refer to the link;
https://brainly.com/question/14042561
which is not one of the ways that codes of ethics can vary from each other?
a. authorship
b. level
c. principle
d. purpose
One of the ways in which code of ethics does not vary from each other is ; ( C ) Principle
What is code of ethics ?Code of ethics is a set of written principles that serves as a guideline to ethical behaviors expected from individuals under some form of authority usually at the place of work.
Code of ethics is different from code conduct because code of conduct is a set of rules that oultines the proper practices of individuals at the place of work. The code of ethics vary in autorship, level and purpose.
Hence we can conclude that One of the ways in which code of ethics does not vary from each other is ; ( C ) Principle
Learn more about Code of ethics : https://brainly.com/question/25717861
What are the three main guidelines in psychological research?
Answer:
Ethical Guidelines for Research With Human Subjects
Participation Must Be Voluntary.
Researchers Must Obtain Informed Consent.
Researchers Must Maintain Participant Confidentiality
Explanation:
Basta Yun na yan correct me if I'm wrong hehehhe
when a block is made of _____ the cylinders may eventually wear to the point where repairs are ineffective
When a block is made of rough surfaces, the cylinders may eventually wear to the point where repairs are ineffective.
What is Friction?This is the force which occurs when two surfaces slide against each other. A rough surface have more friction than a smooth surface.
Friction causes wearing out of surfaces and may render repair works done ineffective in this case.
Read more about Friction here https://brainly.com/question/24338873
How many Watts of power does a model rocket engine have if it does 66 J of work on a model rocket in 0.9 seconds?
Power developed by a model rocket engine will be 73.3 watts. Power is the ratio of the work done or the enrgy to the time period.
What is the power output?The rate of the work done is called the power output. It is denoted by P.Its unit of a watt.
The given data in the problem is;
E is the energy = 66 J
P is the power output =?
t is the time period = 0.9 sec
The power output is given as;
[tex]\rm P = \frac{E}{t} \\\\ \rm P = \frac{66}{0.9} \\\\ \rm P = 73.3 \ watt[/tex]
Hence power developed by a model rocket engine will be 73.3 watts.
To learn more about the power output refer to the link;
https://brainly.com/question/22285866
#SPJ1
Which of the following can explains convection?
A.Hot air is less dense than cold air.
B.The wind blow takes place from higher position to lower position
C.The particles in hot air are lighter than those in cold air.
D.The gas pressure of hot air is greater than that of cold air.
E.The particles in hot air move quicker than that of cold air.
Answer:
A) would be the best explanation because hot air is less dense and would rise to the top of a column of air
The batteries of some flashlights can be charged by turning a handle. Which energy transformation is happening in this process
The energy transformation that is happening in this process is mechanical energy to chemical energy.
Energy ConversionAccording to conservation of energy, energy can not be distroyed and cannot be created, but can only be transformed from one form to another.
The batteries of some flashlights can be charged by turning a handle. The energy transformation that is happening in this process is mechanical energy to chemical energy. The chemical energy will transform to electrical energy which will eventually transform to light energy.
The turning of the handle is mechanical and the energy in battery is chemical.
Learn more about Energy here: https://brainly.com/question/25959744
m=3000km v=25m/s what’s the momentum
Momentum of the given body will be : 75000 Kg m/s
Explanation:According to Newton's first law of motion, all bodies continue to be in the state of rest or motion unless an external force is applied on the body. We can use this in the case of momentum also
The formula of momentum is given by :
[tex]:\implies \sf\quad \sf \: P = mv[/tex]
Here, we are given the mass of the body ( m ) as 3000kg and the velocity of the body ( v ) as 25 m/s. On putting the values in the formula:
[tex] \begin{aligned}&:\implies \sf\quad \sf \: P = mv \\& :\implies \sf\quad \sf \: P = 3000 \times 25 \\ & :\implies \sf\quad \sf \: \boxed{ \sf \: P = 75000kgm {s}^{ - 1} } \end{aligned}[/tex]
Momentum is associated with the mass of the moving body and can be defined as the quantity of motion measured as a product of mass and velocity.
Answer :-
Momentum is [tex] \bf{75,000 \: {kg \: ms}^{ - 1} } [/tex] .Explanation :-
As per the provided information in the given question, we have been given that The Mass is 3000 kg . The Velocity is given as 25 m/s . And, we have been asked to calculate the Momentum .
For calculating the Momentum , we will use the Formula :-
[tex] \bigstar \: \: \: \boxed {\sf { \: Momentum \: = \: Mass \: \times \: Velocity \: }} [/tex]
Therefore , by Substituting the given values in the above Formula :-
[tex] \dag \: \: \: \sf { Momentum \: = \: Mass \: \times \: Velocity} [/tex]
[tex] \Longrightarrow \: \: \: \sf { Momentum \: = \: 3000 \: \times \: 25} [/tex]
[tex] \Longrightarrow \: \: \: \textbf {\textsf {Momentum \: = \: 75000 }} [/tex]
Hence :-
Momentum = [tex] \bf{75,000 \: {kg \: ms}^{ - 1} } [/tex] .[tex] \underline {\rule {180pt} {4pt}} [/tex]
A spaceship moves at a constant velocity of 0.400c relative to an Earth observer. The pilot of the spaceship is holding a rod, which he measures to be 1.00 m long. The rod is held perpendicular to the direction of motion of the spaceship. How long is the rod according to the Earth observer
Since the rod is held perpendicular to the direction of motion of the spaceship, the rod is 1.00 m long to an Earth observer.
To answer the question, we use the principle of length contraction in relativity.
What is Length contraction?The principle of length contraction states that the length of an object would only contraction when it is in the direction of motion.
So, since the 1.00 m long rod is in the spaceship is held perpendicular to the direction of motion of the spaceship, there is no length contraction and thus, an observer on the Earth measures the same length of 1.00 m.
So, Since the rod is held perpendicular to the direction of motion of the spaceship, the rod is 1.00 m long to an Earth observer.
Learn more about length contraction here:
https://brainly.com/question/17407131
