Answer:
F = 750N
Explanation:
We know that F(force) = mass(m) × acceleration(a)
And that Acceleration(a) = velocity(V) ÷ time(t)
So we'll first calculate the acceleration
a = V = 8m/s = 1m/s²
t 8
Next we'll calculate the force
F = ma = 750kg × 1m/s² = 750N
12
9. An empty, massless cube is measured to have all sides equal to 11 cm. It is floating in water and will slowly be filled with sand
that has a density of 3.5 g/cm'. What volume of sand will cause the box to sink?
Answer:
See below ~
Explanation:
An object will sink in water when its density is greater than that of water, which is 1 g/cm³.
Volume of the box is 1331 cm³. (11³)
Maximum mass of sand will be 1331 g. [because 1331/1331 = 1 g/cm³]
Volume of sand = Mass of sand / Density of sandVolume (sand) = 1331/3.5Volume (sand) = 380.29 cm³If the volume of sand is greater than 380.29 cm³, the box will sink in water.
What spectrum can humans see? What does it break into? What is the order of color?
Answer:
the rainbow spectrum. red orange yellow green blue violet. It breaks into ultra violet.
Explanation:
At what time did time begin
50 points :)
Answer:
According to the standard big bang model of cosmology, time began together with the universe in a singularity approximately 14 billion years ago.
Explanation: the big bang
Answer:
approximately 14 billion years ago
What is the difference between heat capacity and specific heat?
don't spam -_++
Heat capacity is the amount of heat required to raise the temperature of an object by 1oC. The specific heat of a substance is the amount of energy required to raise the temperature of 1 gram of the substance by 1oC.
☆...hope this helps...☆
_♡_mashi_♡_
Why is it not easy to witness
inertia on Earth?
A. Magnetism is much stronger.
B. Gravity and friction are always acting on
objects.
C. Our mass is too small.
D. Our mass is too large.
What is the voltage in a cirucit with a current of 3.0 amps and a resistance of 2.0 Ohms?
Answer:
6 v
Explanation:
V = IR
= 3 A * 2 ohm = 6 v
A common practice for a person with a high fever is to take a bath in cool water. Assuming an 80 kg person is really ill and needs to cool down from 40°C to 37°C. What is the minimum amount of water needed for bathing assuming the water begins at room temperature, 25°C?
The minimum amount of water needed for bathing assuming the water begins at room temperature is 16.58kg.
What is thermal equilibrium?When two bodies at different temperature come into contact, they share the heat through conduction. After some time, temperature of both becomes equal. This condition is said to be a body in thermal equilibrium with other.
Heat gained by the water = heat lost by the ill person
m x Cw x ΔT = M x Cp x Δt
where, mass of person M = 80kg, Cp =specific heat of body =3470, specific heat of water Cw= 4186, then mass of water m will be
m x 4186 x (37-25) =- 80 x 3470 x (37-40)
m = 16.58kg
Thus, the mass of water needed is 16.58kg.
Learn more about thermal equilibrium.
https://brainly.com/question/14473445
#SPJ1
DOES THE SUN CONTAIN NUCLEAR ENERGY?
Answer: yes
Explanation: it's fueled by nuclear reactions that fuse hydrogen atoms together into helium and other heavier elements, releasing huge amounts of energy in the process.
How hot must a star get before it becomes a star?
Answer: 10 million degrees
Explanation:
Hope this helps :)
A 9-volt battery is connected to a 4-ohm resistor and a 5-ohm resistor as shown in the diagram above. How much current flows through the 4-ohm resistor?
1.0 A
1.8 B
2.3 C
4.0 D
The current flowing in the 4 ohms resistor connected in series with 5-ohm resistor is determined as 1.0 A.
Equivalent resistance of the circuit
The equivalent resistance of the circuit is determine as follows;
Rt = R1 + R2
Rt = 4 ohms + 5 ohms = 9 ohms
Current flowing in the 4 ohms resistorThe current flowing in the 4 ohms resistor is determined from Ohms law as shown below;
V = IR
I = V/R
I = 9/9
I = 1.0 A
Since the circuit is in series arrangement, same current will flow in 5 ohm and 4 -ohm.
Learn more about current here: https://brainly.com/question/24858512
#SPJ1
Which best explains horatio’s error? magnetism is not produced by electric currents unless the wire is coiled. the magnetic field does not continually spread outward from the wire. the magnetic field is produced inside the wire, not outside of it. magnetism is only produced when a metal bar is placed near the wire.
What best explains Horatio’s error is the magnetic field does not continually spread outward from the wire. Option B. This is further explained below.
What is a Magnetic field?Generally, a Magnetic field is simply defined as an area of magnetism that exists around a magnetic substance or a moving electric charge.
In conclusion, The magnetic field does not continuously expand outward from the wire, which best explains Horatio's miscalculation.
Read more about Magnets
https://brainly.com/question/7802337
#SPJ4
Answer:
B
Explanation:
Can someone please answer this, ill give you brainliest Would be very appreciated.
[tex]{\large{\red{\mapsto{\maltese{\underline{\green{\boxed{\blue{\underbrace{\overbrace{\pink{\pmb{\bf{Answer:}}}}}}}}}}}}}}[/tex]
Weather
Explanation:
As during climate only one season change to another and it's a long period of time
while in weather it's can change into any season for few days depending on the relief of the area.
Answer:
weather
Explanation:
There is often confusion between weather and climate. Weather is the condition of the atmosphere at a particular place over a short period of time.
explain what uncertainty is and how you would calculate the uncertainty of a mean result
Answer:
https://stats.stackexchange.com/questions/454120/how-can-i-calculate-uncertainty-of-the-mean-of-a-set-of-samples-with-different-u
Explanation:
The speed of light traveling through an unknown material is 1.98×108 m/s. Given that the speed of light in a vacuum is 3.00×108 m/s, what is the dielectric constant of the unknown material?
The dielectric constant of the unknown material is 2.3.
What is dielectric constant?Dielectric constant is referred as a relative permittivity or amount of charge required to produce one unit of electric flux in a given medium.
Given the speed of light in vacuum c =3 x 10⁸ m/s and the speed of light through an unknown material v = 1.98 x 10⁸ m/s.
The dielectric constant is related to the velocity by the following relation,
v = c/√K
Rearranging for dielectric constant, we get
K = (c/v)²
Substitute the value into the expression ,we get
K =(3 x 10⁸ / 1.98 x 10⁸)²
K = 2.3
Thus, the dielectric constant of the unknown material is 2.3.
Learn more about dielectric constant.
https://brainly.com/question/13265076
#SPJ1
What is the potential difference if the current of 2A flow in 5sec in wire,total energy in wire to flow the charge is 500J.please its urgent.
Given the total energy in the wire, current and time elapsed, the potential difference is 50 Volts.
What is the potential difference?The electric power is expressed as P = VI.
Where V is the potential difference, I is the electric current and P is the electric power.
Also, the consumption of energy per unit of time is called power. It is expressed as P = E / t
Given that;
Current I = 2.00AElapsed time t = 5sTotal energy E = 500JFirst, we determine the power.
P = E / t
P = 500J / 5s
Power = 100W
Next, we determine the potential difference.
P = V × I
V = P / I
V = 100W / 2.00A
V = 50V
Given the total energy in the wire, current and time elapsed, the potential difference is 50 Volts.
Learn more about Ohm's Law here: brainly.com/question/12948166.
#SPJ1
The Potential difference is 50 Volts.
What is the potential difference?The potential difference is a measure of the energy given to the charge carriers in a circuit
We know that the electric power is expressed as P = VI.
V is the potential difference
I is the electric current
P is the electric power.
Also we know that power is expressed as P = E / t
Given
Current( I) = 2.00A ,time t = 5s
Total energy E = 500J
To find the power
P = E / t = 500J / 5s = 100W
Now , To find the potential difference.
P = V × I (By rearranging it)
V = P / I
V = 100W / 2.00A = 50 V
Therefore , the total energy in the wire, current and time elapsed, the potential difference is 50 V.
For more potential difference related question visit here:
https://brainly.com/question/15136290
#SPJ1
Which of these elements would be the best
semiconductor?
O Ar
O Se
O Rh
O Po
Answer
Its PO
Explanation:
I got it right on Edge.
Is a cow a producer? Or a consumer or decomposer?
Answer:
cows a consumer
Explanation:
because it can make food by its own
A uniform conducting rod of length 23 cm has a potential difference across its ends equal to 66 mV (millivolts). What is the magnitude of the electric field inside the conductor in units of N/C
The magnitude of the electric field inside the conductor will be 0.208 N/C.
What is an electric field?An electric field is an electric property that is connected with any location in space where a charge exists in any form. The electric force per unit charge is another term for an electric field.
Given data;
length of rod = 25 cm = 0.25 m
Potential Difference = 52 mV = 0.052 Volts
The electric field is found as the ratio of the potential difference and the length;
[tex]\rm E =\frac{0.052}{0.25} \\\\ E=0.208 \ N/C[/tex]
Hence,the magnitude of the electric field inside the conductor will be 0.208 N/C.
To learn more about the electric field refer to the link;
https://brainly.com/question/26690770
#SPJ1
Before you start your engine, __________ A. adjust the seat so you can reach all controls. B. make sure your car is in reverse or neutral gear before starting the engine. C. move your car before you have looked in front, behind and to the side for pedestrians and oncoming traffic. D. all of the above
Answer:
A. adjust the seat so you can reach all controls
------------------------------------------------------
This is so you can reach the gas petal, break petal, steering wheel, (and other things) easier so you won't have to lean forward and it makes it easier for when you're driving. Especially if you need to quickly press your breaks, you'll be able to do this a lot faster if you're closer to them than if you had to reach in order to do so.
I hope this helped, im not the best at explaining things lol
Identify which portions of the electromagnetic spectrum are used in each of the devices listed. a. a microwave oven b. a television set c. a single-lens reflex camera
The portions of the electromagnetic spectrum are used in the television set. It is used in the picture tube in the old television set.
What is the electromagnetic spectrum ?The electromagnetic radiation distribution in accordance with the frequency or wavelength is known as the electromagnetic spectrum.
The portions of the electromagnetic spectrum are used in the television set. It is used in the picture tube in the old television set.
Hence, option b is correct.
To learn more about the electromagnetic spectrum, refer to the link;
https://brainly.com/question/15576247
#SPJ1
The masses of two objects are 2 kg and 8 kg, respectively.If their kinetic energies are in 2:1 proportion, the ratio of their speeds is ___.
√2 :1
1:2
2√2 :1
Let's see
[tex]\\ \rm\Rrightarrow \dfrac{KE_1}{KE_2}=\dfrac{2}{1}[/tex]
[tex]\\ \rm\Rrightarrow \dfrac{0.5(2)v_1^2}{0.5(8v_2^2)}=\dfrac{2}{1}[/tex]
[tex]\\ \rm\Rrightarrow \dfrac{v_1^2}{4v_2^2}=\dfrac{2}{1}[/tex]
[tex]\\ \rm\Rrightarrow v_1^2=8v_2^2[/tex]
[tex]\\ \rm\Rrightarrow \dfrac{v_1^2}{v_2^2}=\dfrac{8}{1}[/tex]
[tex]\\ \rm\Rrightarrow \dfrac{v_1}{v_2}=\dfrac{2\sqrt{2}}{1}[/tex]
[tex]\\ \rm\Rrightarrow v_1:v_2=2\sqrt{2}:1[/tex]
#BBH
True or false: when two objects are rubbed together they both will have either a positive charge or both be negatively charged. Causing them to then repel each other. (1 Point) True False not enough information Maybe
Answer:
true
Explanation:
because rubbing together they will both have friction
The half-life of radium-226 is 1,600 years and the half-life of carbon-14 is 5,730 years. In 1-2 sentences, mathematically prove that the decay constant for radium-226 is larger than the decay constant for carbon-14.
The decay constant for radium-226 is larger than the decay constant for carbon-14 due to its obtained value.
What is the rate of decay?
The reduction in the number of radionuclides per unit time is the rate of decay.
The decay constant of the radium-226 is;
[tex]\lambda_1=\frac{ 16}{100}\times 266 \\\\ \lambda_1= -36.16[/tex]
The decay constant of the carbon-14 is;
[tex]\lambda_2=\frac{ -57.3}{100}\times 14 \\\\ \lambda_1= -802.2[/tex]
Hence, the decay constant for radium-226 is larger than the decay constant for carbon-14.
To learn more about the rate of decay refer to the link;
https://brainly.com/question/14486631
#SPJ1
Answer:
0.693/1600 > 0.693/5730
Explanation:
The decay constant is the reciprocal of the time it takes for the radioactivity to decline to about 36.8% of its original value. It is the value of k in the multiplier e^(-kt), which tells the fraction remaining after time t.
When compared to the half-life, h, the value of k is ...
k = 0.693/h . . . . . decay constant for half-life h
Effectively, the decay constant is proportional to the inverse of the half-life. The constant of proportionality is ln(2) ≈ 0.693.
__
decay constant for radium-226:
0.693/1600 ≈ 4.33×10^-4
decay constant for carbon-14:
0.693/5730 ≈ 1.21×10^-4
Since 4.33×10^-4 is greater than 1.21×10^-4, the decay constant of radium-226 is larger than that of carbon-14.
_____
Additional comment
Taking the reciprocal of a positive number reverses the ordering:
1600 < 5730
1/1600 > 1/5730
The half-life of radium-226 is less than that of carbon-14, so its decay constant will be larger.
Which direction will the box move?
Net force
F1-F2-F35-10-205-30-25NAs it's negative the box will move left
What is one way that light waves differ from sound waves?(1 point)
how deep under water would you need to be in order to be at double atomosphric pressure
Answer:
You would need to be 33 feet deep.
Explanation:
How would increasing the magnitude of the charges on two charged particles and decreasing the distance between the particles affect the strength of the electric force between the particles?
We know the formula
F=kq1q2/rSo
if magnitude of charge is increased the force between them also increased.
And if the distance between them is decreased them also the force will be increased.
So Force increases
Please help, im stuck on this question
Answer:
A) .27 A
Explanation:
v = ir
i = v/r
equivalent r = 45 * 90 / (45+90) = 30 ohms ( for the two r in parallel)
i = 8v / 30 ohm = 267 mAmps
When two objects made of different materials are rubbed together, they will attract each other after the charging process.Immersive Reader (1 Point) True False
Answer:
True
Explanation:
because their is friction(e.g take a ruler rub it in your hair then put it on top of a piece of paper on the table then u will see the process)among the two objects.
If the soccer ball has a mass of 284g, and gravitational force is 9.81 m/s2 on Earth, what is the weight of the soccer ball?
If the watermelon has a mass of 850g, and gravitational force is 9.81 m/s2 on Earth, what is the weight of the watermelon?
Which will hit the ground first?
Answer:
2.79 N8.34 NWatermelonExplanation:
Weight of soccer ball
Weight = mass (in kg) × gravitational forceWeight = 284 x 10⁻³ x 9.81Weight = 0.284 x 9.81Weight = 2.79 N (approximately)Weight of watermelon
Weight = mass (in kg) x gravitational forceWeight = 850 x 10⁻³ x 9.81Weight = 0.85 x 9.81Weight = 8.34 N (approximately)As the watermelon has more weight, it will hit the ground first.